Stringing beads is immediate gratification.  Using these instructions for stringing beads, you can easily make bracelets like the two being modeled by my 4 year-old daughter Zoe in less than an hour.  Aren’t they cute?

About this tutorial: 

These instructions will show you how to string a one-strand bracelet, but you can easily adapt this tutorial for stringing a multi-strand project or a necklace or anklet as well.

Love this website? Give us a “like”

As you get more proficient at stringing, I’m sure you’ll see that you can make dozens of different looks using the same basic technique.  You can add more strands to make a multi strand bracelet or necklace, or use crimps along the length of the cable to create an illusion necklace.

Adding different findings, beads, and dangles can also totally change the look.  But it all starts with this one basic cable stringing technique.

Basic Bracelet Stringing Tutorial

To make a basic strung bracelet, about an hour should do it.



  • 2 pair chain nose pliers or 1 pair flat nose, 1 pair chain nose
  • 1 pair flush cutters


  • 10 inches nylon coated stainless steel stringing cable
  • Toggle clasp
  • 4 crimp tubes or crimp beads
  • your choice of beads

Step 1:

Cut 10″ of stringing cable.

Step 2:

Put a beadstopper or piece of tape on the end of your cable so the beads don’t fall off.

Step 3:

Lay out your design.  I like to start in the middle and work outwards.  You’ll need about 6″ worth of beads for a 7″ wrist.

Step 4:

Start stringing your beads.

Step 5:

Measure the length of your strung beads.  You’ll need about the same amount as your wrist size less one inch. (The extra inch is for your clasp).

Step 6:

Take the tape off one end of your cable, take off last bead strung, then string a crimp tube, the bead you just removed, another crimp tube, then one half of your toggle clasp.

Step 7:

String the end of your cable back through the 1st crimp tube, the bead, and the 2nd crimp tube.

 (Remember to leave enough length on the other end!)

Step 8:

Snug everything up nice and squoosh each crimp tube with your chain nose pliers. 

Give the end a tug to make sure everything is secure.

Step 9:

Do the same on the other end with your remaining half of the toggle clasp.

Step 10:

Try on your bracelet for one last size check.

Step 11:

If everything is A-OK size-wise, trim the ends of cable with your flush cutters.

The Finished Bracelet!



Having a little trouble with these instructions for stringing beads?  Or just looking for some more detailed stringing info?  Here are a few tips:

  • To keep your beads from rolling around, lay out your beads on a bead board, on a towel or bead mat, or on a piece of masking tape secured to a table sticky side up.
  • For extra security, I like to double crimp anything I make.  You can certainly single crimp if you’d like to.
  • When snugging everything up, it helps to hold the loop of the cable with your chain nose pliers.  If you still find it difficult to pull the cable end up tight enough, try pulling using another pair of pliers.
  • You can use crimping pliers to fold the crimp tube over into more of a tube if you like (a little more advanced).  I didn’t mention it above just ‘cuz this is supposed to be a beginner tutorial.
  • If you want to hide the crimps, use the front part of your crimping pliers to gently close crimp covers over each of your crimps.

Other Projects

Here are some other stringing projects you might like to try:

Mother’s Day Bracelet

Grandmother Bracelet

Swarovski Birthstone Bracelet


About the Author

Christine Gierer

I'm Christine Gierer and I'm obsessed with making jewelry and teaching others how to do it too. I've been a creative person all my life, and I've done all kinds of things like art, sociology, and counseling. But nothing makes me happier than playing with beads, wires, and tools and sharing my tips and tricks with you. I have two awesome websites where you can find tons of tutorials, courses, and workshops on how to make jewelry and how to sell it online.

View All Articles